Content
Event Booking
Web Links
Contacts
Tags
Categories
News Feeds
Search - K2

Thoughts & Opinions

Adventures in Stone: Art in a Foreign Country - Sept/Oct 2000

I have enjoyed art in foreign places; I’ve been in awe of Michelangelo’s ‘David’, admired Rodin’s ‘The Thinker’ and stood perplexed at Moore’s ‘The Archer’ in front of city hall in Toronto, Ontario. As a young person growing up there, I heard the great debate over Moore’s “art”. It was condemned by many and lauded by a few, but when Toronto’s new landmark city hall was finished, ‘The Archer’ was placed in front to the amusement of most. Nobody knew what it was supposed to be; the citizens of Ontario in the 1960’s were still pretty conservative. At no time, looking at these pieces of art, did I consider the work that had gone into them, although I realize now that any of those great artists were able to hand off the grunt work to their hired help if they wanted to.


Five years ago, I was fortunate enough to be able to spend a little time in China between Shanghai and Beijing. We toured around by train and bus with a local guide as translator. On one particular day, our bus was taking us somewhere wonderful when I noticed in a yard beside the highway, a large number of stone statues. The sight caught my eye but I didn’t have much time to react. When I realized that we would be taking the same route back, I determined to somehow get the driver to stop for a closer look. That is where the guide came in handy! She must have explained that one particular eccentric foreign woman needed to see the dusty stone yard because we made an unprecedented unscheduled stop!


Limestone sculptures as tall as about 15 feet were scattered around a large yard but only three men labored, all with only hammer and chisel; no safety equipment was in sight! As I gazed around, I heard voices, “Always wear a dust mask,” “Make sure you drink plenty of water.” Ward and Vic were there in my brain. Dust was flying in all directions and the noise by the highway was terrible. One lone old angle grinder lay in a pile of rubble.


The detail on the various pieces was quite fine. There were animals representing strength and endurance, and tall, stern gentlemen emanating intelligence and wisdom. Here in this place, beside a highway, out in the open, not great, but good and enduring art was being created.


What amazed me was that so few people could do so much work on such a grand scale. At the Kong Family tombs, the family of Confucius, and the place of his burial, we had seen many similar statues; the more important the family member the larger the statue. The stone yard had all sizes of statue! I can’t even imagine how much or how little money was paid for these works, but I do know that a hand done ink painting went for approximately seven Canadian dollars (and you all know how much that is!) near the Kong tomb and all of us snatched them up to be taken home as treasures of the trip.


As I work away in my studio at home, with the stereo playing and my respirator and ear plugs in place, I often think of those men and the conditions they laboured under in China

Basing for Dummies, An Easy Alternative to the Stone Problem - Sept/Oct 2000

One of the problems I have faced as a “mostly hand tool, hobby sculptor” is dealing with bases. I took Joanne Duby’s workshops at the Camp Brotherhood Symposium, learned her techniques, and then wasn’t able to implement them myself when I got home. It was frustrating. I simply don’t have the drills, diamond blades, power tools and stone available to me that she uses. Nor was I ready to invest in them for the sake of bases, when hand tooling beautiful things in softer stones was my passion. So I had to invent another way and I utilized the help and tools of my woodworking husband, Peter.


I use MDF (Medium Density Fibreboard) cut to the dimensions that I want for the base of a piece. You can get it at any lumber store in 4' x 8' sheets, like plywood. It comes in various thicknesses, mostly I use the 3/4 “. It cuts like butter so it can be cut with a hand saw or a table saw. When I finish a sculpture, I decide the size and height of the the base I want. I cut enough pieces of the MDF to the same dimensions to get the height I want for my base by stacking the pieces. Then I pile them up and drill a very small hole through the top pieces into the bottom piece. Just big enough for a skinny nail.


We then glue the pieces together with wood glue and stick a nail down through the drill hole to keep them in place and we squeeze the pieces together very tightly with clamps. Be sure to put little flat pieces of wood under the clamp feet or you may make impressions in the MDF. This dries overnight. The next day I pull the nail out, take the clamps off and either use a wood chisel to scrape off the glue that has oozed out from between the pieces or run them through the table saw again to get nice smooth edges.


Then I sand the sides to make sure the glue made a solid bond and to smooth out any discrepancies in the wood surfaces. You don’t want holes in the side of the piece where there is no glue! This MDF is very soft so you have to be careful not to round your top and corner edges in the sanding process.


Putting your sandpaper around a block of wood is the best bet.


Now you have a wood base that is the dimensions you want and YOU CAN LIFT IT by yourself. After sanding I put the base on blocks and paint it. My best results have come from, don’t laugh, Rust-Oleum Painter’s Touch Multi Purpose Paint in SemiGloss Black. It gives the piece a nice sheen without a real shine but is not flat. I put several coats on the wood, lightly sanding between coats. I paint the edges of the bottom side, then glue black felt to cover the entire bottom just up to the edges. If you use one of the cheapo foam brushes, you do not leave any bristle marks.


These bases can be drilled to stabilize a sculpture on a pin, or can just sit there and hold the piece. I have sold sculptures on these bases that were up to $1000 each, and no one seemed to have any complaints about them. I know it isn’t stone, but somehow I find the juxtaposition of the wood with the stone to be complimentary and it solved a big problem for me.

The Sculpture Scene n Bellingham - Sept/Oct 2000

As part of the Bellingham 2000 project, Ward Lynch and Janet Brown set up a week-long “Sculptors at Work” event in August at Maritime Heritage Park in Bellingham. The media were limestone, fabricated metal and wood.


The three artists who were chosen had demonstrated not only their creative abilities, but that they would enjoy interacting with the public and be able to instruct and describe what they were doing. A week was not long enough to insure a finished piece of work, but the excitement of having an idea and translating it into form was definitely communicated to the viewer.


Our own Ruth Mueseler was chosen for the stone demonstration and did a wonderful job at work and communicating with the public as did the other two artists, Chris Pauley with imaginative metal animals, and Jewell James, a Lummi carver working on two 6-foot totems.


The event was sponsored by the Bellingham Art’s Commission and had excellent response from the community. As Kay Moquin envisioned of the “Sculptors At Work” project, “Next year there’ll be more sculptors involved and the year after that even more. A wonderful opportunity for our group.”